高级搜索 返回首页  
名人名言
技术文章
    - LINUX文章
少达网技术文章LINUX文章CentOS7 防火墙(firewall)的操作命令
CentOS7 防火墙(firewall)的操作命令
2021-09-27 10:58:41
by 山阴客  
Rating: not rated yet
1 2 3 4 5 6 7 8 9 10

CentOS7 防火墙(firewall)的操作命令

 

安装:yum install firewalld

 

1、firewalld的基本使用

启动: systemctl start firewalld

查看状态: systemctl status firewalld 

禁用,禁止开机启动: systemctl disable firewalld

停止运行: systemctl stop firewalld

 

 

2.配置firewalld-cmd

查看版本: firewall-cmd --version

查看帮助: firewall-cmd --help

显示状态: firewall-cmd --state

查看所有打开的端口: firewall-cmd --zone=public --list-ports

更新防火墙规则: firewall-cmd --reload

更新防火墙规则,重启服务: firewall-cmd --completely-reload

查看已激活的Zone信息:  firewall-cmd --get-active-zones

查看指定接口所属区域: firewall-cmd --get-zone-of-interface=eth0

拒绝所有包:firewall-cmd --panic-on

取消拒绝状态: firewall-cmd --panic-off

查看是否拒绝: firewall-cmd --query-panic

 

3.信任级别,通过Zone的值指定

drop: 丢弃所有进入的包,而不给出任何响应 
block: 拒绝所有外部发起的连接,允许内部发起的连接 
public: 允许指定的进入连接 
external: 同上,对伪装的进入连接,一般用于路由转发 
dmz: 允许受限制的进入连接 
work: 允许受信任的计算机被限制的进入连接,类似 workgroup 
home: 同上,类似 homegroup 
internal: 同上,范围针对所有互联网用户 
trusted: 信任所有连接

4.firewall开启和关闭端口

以下都是指在public的zone下的操作,不同的Zone只要改变Zone后面的值就可以

添加:

firewall-cmd --zone=public --add-port=80/tcp --permanent    (--permanent永久生效,没有此参数重启后失效)

重新载入:

firewall-cmd --reload

查看:

firewall-cmd --zone=public --query-port=80/tcp

删除:

firewall-cmd --zone=public --remove-port=80/tcp --permanent

 

5.管理服务

以smtp服务为例, 添加到work zone

添加:

firewall-cmd --zone=work --add-service=smtp

查看:

firewall-cmd --zone=work --query-service=smtp

删除:

firewall-cmd --zone=work --remove-service=smtp

 

5.配置 IP 地址伪装

查看:

firewall-cmd --zone=external --query-masquerade

打开:

firewall-cmd --zone=external --add-masquerade

关闭:

firewall-cmd --zone=external --remove-masquerade

 

6.端口转发

打开端口转发,首先需要打开IP地址伪装

  firewall-cmd --zone=external --add-masquerade

 

转发 tcp 22 端口至 3753:

firewall-cmd --zone=external --add-forward-port=22:porto=tcp:toport=3753

转发端口数据至另一个IP的相同端口:

firewall-cmd --zone=external --add-forward-port=22:porto=tcp:toaddr=192.168.1.112

转发端口数据至另一个IP的 3753 端口:

firewall-cmd --zone=external --add-forward-port=22:porto=tcp::toport=3753:toaddr=192.168.1.112

 

6.systemctl是CentOS7的服务管理工具中主要的工具,它融合之前service和chkconfig的功能于一体。

启动一个服务:systemctl start firewalld.service
关闭一个服务:systemctl stop firewalld.service
重启一个服务:systemctl restart firewalld.service
显示一个服务的状态:systemctl status firewalld.service
在开机时启用一个服务:systemctl enable firewalld.service
在开机时禁用一个服务:systemctl disable firewalld.service
查看服务是否开机启动:systemctl is-enabled firewalld.service
查看已启动的服务列表:systemctl list-unit-files|grep enabled
查看启动失败的服务列表:systemctl --failed

推荐给好??? 打包下载这篇文章 打印这篇文章

Copyright © 2002-2022 http://www.shaoda.com
All rights reserved.

备案号:浙ICP备17002154号-5 Powered by: myarticle.com.cn Version 1.0dev
Processed Time: 0.0029 s Querys: 5 [ Gzip Level 0 ]